Do not want to start XP, such as the speed of the speed!

Computer users are often heard complaining about this: how self-inspection after I opened the computer screen is black, only half a day to the XP interface appears » I entered the computer systems doing so slow » Scroll bar are also to the more than 10 laps into the system can not. Why is my XP desktop appears after a few minutes click on any of the procedures have no reaction » These problems can be summed up as Windows XP slow start. How can we do to accelerate the start-up rate system? »
XP slow start to solve the problem, we must first understand the system start-up process. Windows XP activation process can be broadly classified into five steps: first step, the pre-start: First of all computer power for self-inspection by the BIOS (basic input output system that is) scanning hardware and complete the basic hardware configuration, and then drive to read the MBR (Master boot record) check your hard disk partition table to determine the guiding Division, and will guide the district on the operating system boot sector in the implementation of the redeployment of memory, here is the implementation of NTLDR (operating system to load) document. The second step to start: First and only to, NTLDR is from the processor model will be converted to 32 protected mode. BOOT.INI and then read the document. The third step is. Loading kernel: to guide the process began loading XP core NTOSKRNL.EXE. This file is in Windows2000/XP installation folder under the SYSTEM32 folder. Subsequently, the Hardware Abstraction Layer (HAL) was to guide the process of loading, the completion of this step. The fourth step, the initial core: core complete initialization, NTLDR will be handed over to the control of the core Windows2000/XP, which began loading device drivers and initialization and start WIN32 subsystem and WINDOWSXP services. Step 5 is the user login, login, XP will continue to configure network equipment and user environment. Finally, accompanied by a system reboot music and we are familiar with the desktop, Windows XP start the long process was finally completed.
Understanding of the XP activation process, we can in a targeted manner to take measures to expedite the start of speed.
1, does not prohibit use of peripherals
Through the process before the start of the understanding we know, XP will be automatically activated in the scanning hardware, so if the WinXP disable some peripherals, system can effectively reduce the need to start the redeployment of the number of peripheral drivers, so as to speed up The start-up system speed. If your computer has no USB devices, in the "Device Manager - Universal Serial Bus controllers" will disable all USB devices. This method allows you to the XP start-up time reduced by about 15 seconds. Secondly, if you do not have multiple hard drives, can also ban certain IDE equipment to speed up the launch speed. Is: Right-click on the "My Computer - Properties", then click the "hardware" and then click on "Device Manager", which opened in the "IDE ATA / PATA controller" (a slight difference between different chips), and then separately to main And secondary IDE channel, select "Advanced Settings", located here, "the current transmission" as "not applicable" a (This is the idle channel corresponding to the IDE), this will be the "equipment type" is set to "Nil", can be identified. In addition to Note: Due to the default system will automatically read the drive, the drive will start at the test, if placed in the CD-ROM drive, it will automatically read, if a multimedia CD-ROM so readers will spend a longer time , To extend the same computer's start-up time. Therefore, we usually use the proposed recall timely End CD taken out.
2, to reduce the load at startup procedures
Many people probably have this feeling: XP start-up speed of the initial installation of the system is still relatively fast, but with the installation of the software continue to increase, the rate will start increasing slowly. This is because many of its own software to increase in the commencement of the proceedings, so that the required start-up operation and greatly reduce the launch speed, but also occupy a large amount of system resources. For some procedures so that we can through the System Configuration Utility Msconfig from the start they will exclude groups. Select "Start" menu in the "Run" commands, "Run" dialog box, type "Msconfig", will return after the pop-up "system configuration utility" dialog box, select one of the "start" tab, the Tab of the system listed in the commencement of the project and the source of loading, carefully looking at each project the need for automatic loading, or remove items before the box, loading the less the item, the faster start . In addition to the proposed reservation input method (for the commencement of the project ctfmon) and antivirus monitoring procedures (such as RavTask), the other to prohibit all his run automatically at startup.